ASTM A Standard Specification for Steel Forgings, General Requirements. to steel forgings under any of the following specifications issued by ASTM. This standard is issued under the fixed designation A/AM; the number . 1 ASTM Standards:3 A/AM Specification for Alloy Steel Forgings for. ASTM A/AMb. Standard Specification for Steel Forgings, General Requirements. standard by ASTM International, 11/01/ View all product details.
|Published (Last):||9 April 2004|
|PDF File Size:||9.28 Mb|
|ePub File Size:||10.7 Mb|
|Price:||Free* [*Free Regsitration Required]|
ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. This specification covers a group of common requirements that, unless covered by the individual product specification in another ASTM document, applies to steel forgings for general use. The chemical composition thus determined shall conform to the requirements of the product speci?
ASTM A – 02 Standard Specification for Steel Forgings, General Requirements NO_PDF
Such requirements to be considered include, but are not restricted to, the following: Tension and hardness tests shall be conducted to evaluate mechanical properties such as the percentage of elongation and reduction of area. If you feel that your comments have not received a fair hearing aatm should make your views known to the ASTM Committee on Standards, at the address shown below.
Plot the percentage shear fracture against test temperature and determine the transition temperature by interpolation extrapolation is not permitted. Level S—Shear Wave S Combining values from the two systems may result in non-conformance with the standard.
It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations zstm to use.
Details of heat and product analyses for the evaluation of chemical composition are thoroughly discussed.
The molten metal shall be adequately stirred for a sufficient length of time to maximize exposure to the evacuated atmosphere. Open-ended molds, which are usually cooled and used, for example, in the continuous casting of steel, are considered to be included in this de?
The primary melting may incorporate separate degassing or refining and may be followed by secondary melting, asrm electro slag ESR or vacuum arc remelting VAR.
This steel is forged through various process depending upon the temperature at which it is done.
ASTM A788 Stainless Steel Forged Fittings Suppliers
Sometimes referred to as a solid forging. The evacuation system shall be capable of reducing the pressure aetm, which occur each time a new portion of steel is admitted to the vessel to increasingly lower levels, until a blank-off pressure usually less than ? Repair welding shall not be allowed unless permitted by the product specification. Step 1—Determine furnace factor FF for each heat based on weight.
The bar coding system, if applied at the discretion of the supplier, should be consistent with one of published industry standards for bar coding. The purchaser shall furnish the manufacturer with details of the desired heat treatment for the test coupons, x788 temperatures, times, and cooling rates. In modern times, industrial forging is done either a88 presses or with hammers powered by compressed air, electricity, hydraulics or steam.
However, when multiple austenitizing stages are used the temperature for the last may be set between the upper Ac3 and lower Ac1 critical temperature for partial austenitizing.
ASTM A / AM – 18b Standard Specification for Steel Forgings, General Requirements
Link to Active This link will always route to the current Active version of the standard. The primary melting may incorporate separate degassing or refining and may be followed by secondary melting, using electro slag Qstm or vacuum arc remelting VAR.
ASTM A specification applies to steel forgings for general use. For analysis from each remelted ingot, see S Siddhagiri Metals and Tubes Rating: The material is then reheated to a temperature in the intercrtical range between the Ac1 and the Ac3 and again cooled below the Ac1, followed by subcritical tempering in the range speci?
Forgings of large size are commonly used by industrial equipment and machinery such as steel, textile, paper, power generation and transmission, chemical and refinery industries. Historical Version s – view previous versions of standard.
The capacity of the system must also be sufficiently high to reduce the initial surge pressure at the start of the pour to a low level within 2 min.
Repair welding shall not be allowed unless permitted by the product specification. Ultrasonic Examination from Bore Surface S Details of heat and product analyses for the evaluation of chemical composition are thoroughly discussed with the expertise.
A number in parentheses indicates the year of last reapproval.